Vog omid golestan

wafer butterfly valve

• Unbreakable cast iron body and impeller-GGG40 • Propeller with galvanized coating or electrostatic paint coating according to order • Body color: blue powder epoxy by electrostatic method according to the standard DIN30677 Specifications: • The body is suitable for installation between flanges with matching holes Standard (1 Part 2501 DIN) up to 10 to 16 bar pressure. It is placed in the middle and provides the best conditions for • Propeller in full open position It creates The flow of C • Sealing rubber inside the body, replaceable and sealing you can be sure of It provides both directions. • The thickness of the valve is according to EN558-20 or 5752 ISO-20. • Disconnecting lever and connecting to the indicator made of aluminum (dycast) Uses: • For water up to 80 degrees Celsius and for higher temperatures according to order is provided Components: • Body: cast iron GGG40 • Bushes: graphite bronze • Rubber sealing: NBR or EPDM • Propeller: - GGG40 with galvanized coating • Shafts: Steel 4021 / 1 • O-rings: NBR • Screws: A

wafer butterfly valve

• Unbreakable cast iron body and impeller-GGG40 • Propeller with galvanized coating or electrostatic paint coating according to order • Body color: blue powder epoxy by electrostatic method according to the standard DIN30677 Specifications: • The body is suitable for installation between flanges with matching holes Standard (1 Part 2501 DIN) up to 10 to 16 bar pressure. It is placed in the middle and provides the best conditions for • Propeller in full open position It creates The flow of C • Sealing rubber inside the body, replaceable and sealing you can be sure of It provides both directions. • The thickness of the valve is according to EN558-20 or 5752 ISO-20. • Disconnecting lever and connecting to the indicator made of aluminum (dycast) Uses: • For water up to 80 degrees Celsius and for higher temperatures according to order is provided Components: • Body: cast iron GGG40 • Bushes: graphite bronze • Rubber sealing: NBR or EPDM • Propeller: - GGG40 with galvanized coating • Shafts: Steel 4021 / 1 • O-rings: NBR • Screws: A

globe valve

The length of the flange is based on DIN 3202F1 • Working pressure: 10 and 16 atmospheres • Test pressure: 1.5 times the nominal pressure • Color: electrostatic powder • Maximum temperature of 180 degrees Celsius: cast iron PN16 • Dimensions of flanges according to DIN 2501 - E standard Specifications: • Da Ketil 40-GGG body and cover • Diecast aluminum armrest • Sealing nut with graphite and 2 NBR or silicone O-rings • Screws according to DIN 931 Steel standard • Body cover gasket made of non-combustible material • Stainless steel waterproofing site 4021.1 (X20Cr13) Topiaz Zangenzen 4021.1 (X20Cr13) • Mardon Shir (shaft) stainless steel 4021.1 (X20Cr13) Flange holes are in accordance with EN1092-1 Part-DIN2501 standard • Fully waterproof paint coating by electrostatic method 30677 D Uses: • In water and steam facilities up to a maximum temperature of 180 degrees Celsius

globe valve

The length of the flange is based on DIN 3202F1 • Working pressure: 10 and 16 atmospheres • Test pressure: 1.5 times the nominal pressure • Color: electrostatic powder • Maximum temperature of 180 degrees Celsius: cast iron PN16 • Dimensions of flanges according to DIN 2501 - E standard Specifications: • Da Ketil 40-GGG body and cover • Diecast aluminum armrest • Sealing nut with graphite and 2 NBR or silicone O-rings • Screws according to DIN 931 Steel standard • Body cover gasket made of non-combustible material • Stainless steel waterproofing site 4021.1 (X20Cr13) Topiaz Zangenzen 4021.1 (X20Cr13) • Mardon Shir (shaft) stainless steel 4021.1 (X20Cr13) Flange holes are in accordance with EN1092-1 Part-DIN2501 standard • Fully waterproof paint coating by electrostatic method 30677 D Uses: • In water and steam facilities up to a maximum temperature of 180 degrees Celsius

sliding gate valve flange

DN 100 - DN 1000 size pressure PN6 - PN10 - PN16 - PN25 Specifications: • Valve design according to EN DIN 593 standard (DIN3354) • Flanges and flanges according to standard F4-3202 DIN) 14 series 1-558 EN (DIN • Dimensions of the flange according to EN DIN 1092-2 standard (DIN 2501) • Off-center bearing of the propeller in the body • Designing the disk in such a way that its resistance to fluid flow is minimal • Ability to install in all situations (horizontal, vertical, at an angle) • All bolts and nuts of the valve that are in contact with water are stainless steel. • Ability to install Royshir Electrokiber actuator • The ability to adjust and replace the sealing rubber without removing the valve Installation The ability to replace the gearbox without cutting the transmission lines • Machining the seat of the valve actuator in accordance with the ISO 5201 standard • Machining of gear box valve according to ISO 5211 standard • Ability to seal from both directions • Closing the valve with a handwheel in clockwise direction Uses: • Non-liquid butterfly valves such as raw water, drinking water and non-corrosive liquids It is used up to a temperature of 70 degrees Celsius to disconnect and connect the current Butterfly valves in transmission lines should not be allowed as flow controllers be in open or closed state.

sliding gate valve flange-bronze

• Design based on Iranian standard 16/10 PN 3363 • Flange length 3202F4 D Specifications: • CuSn5PB20 bronze alloy body and cap • CuSn5PB20 bronze alloy sealing seat • CuSn5PB20 bronze alloy square tongue and nut • Mardon (axis) CuSn5PB20 bronze alloy valve • CuSn5PB20 bronze alloy hexagonal nut • DIN-TE 103 rolling gear • NBR or EPMD cover gasket • Flange hole according to DIN 2501 - EN1092 standard • The armrest head is made of die-cast aluminum or CuSn5pB20

sliding gate valve flange-bronze

• Design based on Iranian standard 16/10 PN 3363 • Flange length 3202F4 D Specifications: • CuSn5PB20 bronze alloy body and cap • CuSn5PB20 bronze alloy sealing seat • CuSn5PB20 bronze alloy square tongue and nut • Mardon (axis) CuSn5PB20 bronze alloy valve • CuSn5PB20 bronze alloy hexagonal nut • DIN-TE 103 rolling gear • NBR or EPMD cover gasket • Flange hole according to DIN 2501 - EN1092 standard • The armrest head is made of die-cast aluminum or CuSn5pB20

strainer Y type

• The length of the flange and flange base DIN 3202-F1 PN10/16 Specifications: • Da KetilGGG40 body and cover • Zangenzen 4021.1 (X20Cr13) Abendifwald seat and valve • GGG 50-40 valve lever • Screws according to standard 931 DIN 8.8 Steel • NBR or EPDM cover gasket • The flange holes are in accordance with DIN2501-Part 1 - EN1092 • Complete epoxy paint coating with electrostatic method according to DIN30677 • Unbreakable cast iron sealing valve with EPDM or bronze coating Uses: • In facilities including potable water and non-corrosive liquids up to 90 degrees Celsius and higher temperatures can be provided upon request.

strainer Y type

• The length of the flange and flange base DIN 3202-F1 PN10/16 Specifications: • Da KetilGGG40 body and cover • Zangenzen 4021.1 (X20Cr13) Abendifwald seat and valve • GGG 50-40 valve lever • Screws according to standard 931 DIN 8.8 Steel • NBR or EPDM cover gasket • The flange holes are in accordance with DIN2501-Part 1 - EN1092 • Complete epoxy paint coating with electrostatic method according to DIN30677 • Unbreakable cast iron sealing valve with EPDM or bronze coating Uses: • In facilities including potable water and non-corrosive liquids up to 90 degrees Celsius and higher temperatures can be provided upon request.